Search our Online Products
Search Phrase or Part #:   
 
SHOP BY CATEGORY
Simpson Connectors
Quick Drive Systems
Anchoring Masonry/Concrete
Architectural Connectors
Fastening To Wood
Framing
Hardy Frames
SHOP BY BRAND
Simpson Strong-Tie
HARDY FRAMES
VIEW ALL BRANDS
Simpson Connectors > HGA-KT / Gussett Angle Kit > STANDARD G90 Galvanization
Simpson Strong-Tie SEISMIC & HURRICANE TIE 14GA (Priced Per Each)  View Printable Version
 SEISMIC & HURRICANE TIE 14GA (Priced Per Each)

Manufacturer:
Simpson Strong-Tie - see all
Manuf. Part #:
HGAM10KTA
Our Part #:
SIM HGAM10KTA


Our Price: $45.44
  Qty:  

HGAM10 INSTALLED

HGAM10KT LOAD
 
SIMPSON STRONG-TIE SEISMIC & HURRICANE TIE 14GA (PRICED PER EACH)

HGAM10KT - Wood to Masonry Application 14 GA 3" x 3" x 3-1/2" 

Priced for sale as (1) Kit. Kit includes (10) brackets and most· installation screws for (10) brackets [ (4) SDS 1/4 x 1-1/2 Rafter to Truss & (4) Titen 1/4 x 2-3/4 To CMU ·Note 1/4 x 1-3/4 Titen To Concrete SOLD SEPARATELY].


Full case count is (6) Kits.


Also See -HGA10KT - Wood to Wood Application 14 GA 3" x 2" x 3-1/2"


Priced for sale as (1) Kit. Kit includes (10) brackets and all installation screws for (10) brackets [ (4) SDS 1/4 x 1-1/2 Rafter to Truss & (4) SDS 1/4 x 3 To Plates ].


Full case count is (6) Kits.


The Hurricane Tie series features various configurations of wind and seismic ties for trusses and rafters.


The new H10S provides a high capacity connection from truss/rafter to wall. Also suitable for WOOD TO WOOD

The HM9 is designed to retrofit roof truss/rafters for block construction. The HM9 hurricane tie provides high uplift and lateral capacity using Simpson concrete fasteners.

The presloped 5:12 seat of the H16 provides for a tight fit and reduced deflection. The strap length provides for various truss heights up to a maximum of 13 1/2". Minimum heel height for H16 series is 4".

The LTA1 develops high uplift and lateral loads at a minimum heel height. The side tabs act as a locator in the block and the four embedded hooks allow for higher loads with a relatively shallow embedment.

 

Finish: Galvanized

Installation:



  • Use all specified fasteners.
  • HGAM10 can be installed into grouted concrete block. Screws are provided.
  • Hurricane Ties do not replace solid blocking.
  • Attach to grouted concrete block with a minimum one #5 rebar horizontal in the top lintel block.

Load Table Info



  1. Loads have been increased 33% and 60% for earthquake or wind loading with no further increase allowed; reduce where
    other loads govern.
  2. Allowable loads are for one anchor. A minimum rafter thickness of 2 1/2" must be used when framing anchors are installed on
    each side of the joist and on the same side of the plate.
  3. The HM9KT and HGAM10KTA come with SDS and 2 1/4" and 2 3/4" TITEN SCREWS respectively. (1 3/4" Titen screws for concrete installations sold separately.)
  4. Minimum edge distance 1 1/2" using TITEN SCREWS 
  5. Table allowable loads were determined using test ultimate/3 or fastener calculation values.
  6. LTA1 - Allowable loads are based on a minimum of 2500 psi grout strength with one #5 horizontal rebar in the shear cone.
  7. NAILS: 10dx1 1/2 = 0.148" dia. x 1 1/2" long. 8dx1 1/2 = 0.131" dia. x 1 1/2" long.

 
  ©2014 Fastening Systems inc. Privacy  | Subscribe | Un-Subscribe |  Terms & Conditions  |  Contact